Manufacturer: Dake
Item Number:1615
New/Used:New
Price:$8,500.00 F.O.B. Houston, TX

SPECIFICATIONS:

Machine Type - H-frame hydraulic powered
Capacity - 50-tons
Ram Travel - 16 inches
Pressing Ram Speed - 11 i.p.m.
Return Ram Speed  - 20 i.p.m.
Horse Power  - 2 HP
Hydraulic Pump Combination power unit
Controls On/Off switch with joystick hydraulic control
Oil Capacity - 3 U.S. gallons approx.
Weight - 1200 lbs
Overall Height - 94 inches
Base Width - 55 inches
Depth - 36 inches
Width Between Uprights - 44 inches
Width Between Table Channels - 8 1/4 inches
Maximum Ram to Table - 41 3/4 inches
Minimum Ram to Table - 0 inches
Voltage • Available 110 / 220-volt single phase
.

STANDARD EQUIPMENT:

Frame
Cylinder
Two forged steel table plates
Pressure Gauge
Lifting Chain

FEATURES:

• Made in the U.S.A.

• 110/220-volt single-phase motor makes for greater portability.

• Welded steel frame for rigidity. Fully assembled.

• Low operating pressures. Operating PSI 3537 at 50 ton.

• Double acting cylinder, utilizes the pulling force to raise and lower the table via chains, eliminating the need for hoist assemblies.

• Fast, quite, dependable, economical price, smooth operating press that is very simple to operate.

• Heavy adjustable table can be set to a comfortable work height. Massive table pins keep table securely in place during the pressing operations.

• Pressure preset and locked out at factory for maximum pressing, Safety relief valve

• The motor is a powerful 2 HP power unit for study quiet oil flow.

• 4-Way valve with joystick control operation for easy one hand machine operation.

• Rapid advance of the ram to the work piece, when contact is made the machine shifts into the pressing mode.

• Two steel table plates
45° 7.5" x 7.5"
30° 4.3" x 74.3"

Rectangle 90° H x W 9" x 18.1"
45° H x W 9" x 9"
30° H x W 9" x 4.3"

Blade: Speed 95, 150, 213, 321 fpm
Size 1" x 11.6' x .035"
(27mm x 3505mm x 0.9mm)
Guides Tungsten Carbide

MACHINE FEATURES

Machine Structure & Design:
► Oversized hydraulic cylinder plus precision ground hinge support and guide the rugged saw frame through the entire cutting cycle. Special wear resistant DU bushing is used to endure durability and long use life.
► Specially designed heavy-duty cast iron swivel center features straight and miter cuts from 90 to 30 deg (backwards) with quick setting and precise positioning. It enables smooth turning of the saw frame for each angle viable via the large easy-to-read mitering scale. Turn Table for material support swivels automatically at miter adjustment.
► Large rugged base with built-in coolant & hydraulic systems offers both sound stability & all-in-one convenience.

Blade Drive:
► A 2 hp motor, heavy-duty reducer, and variable step drive assembly with excellent mechanical design feature the essentials for production cutting.
► The 4-speed transmission is equipped with the best worm gear speed reducer. The worm shaft is hardened and ground. Together, they provide quiet, powerful, and trouble-free drive.

Blade Guidance & Lubrication System:
► Carbide blade guides with roller bearings pre-align the blade before entering carbide blade guides. This feature reduces wear on blade guides and blade, thus enhancing blade life.
► The rigid guide arms are mounted on an extra wide precision ground dovetail slide for more solid and supportive surface. This rigid design owes to use of superior cast-iron which greatly reduces vibration and achieves better cutting result.
► Two additional guides located on a central axis support the blade from the top, giving it extra penetrating force. The carbide guides are relieved to allow coolant flow to lubricate and cool the blade as well as work piece.
Integral coolant system.Blade brush to remove chips from blade gullet.

Control & Automation:
► Down feed rate & cutting pressure control. The feed rate may be adjusted by setting the dial between 0 and 10 via the hydraulic down feed valve. The vast range of adjustment allows proper setting which results in longer blade life, shorter cutting times, and better finishes.
► The control panel is clearly arranged and conveniently located on front of the machine, eliminating the need for the operator to reach over a moving blade.
► Built-in hydraulic unit includes hydraulic motor, pump, and hydraulic tank to offer the convenience
of raising the saw head automatically after cut-off. This advanced built-in design with quality components will bring you noiseless and hassle-free operation.
► A work height selector is located over the hydraulic cylinder and is used to adjust the blade to minimum clearance height over the work.

Material Clamping & Feeding:
► Cast iron vises with replaceable extension plate
Secure clamping via a dependable manual lead screw system with anti-slip hand wheel. base with built-in coolant & hydraulic systems offers both sound stability & all-in-one convenience.

Presses, Hydraulics - New

Manufacturer: Dake
Item Number: 1615
New/Used: New
Price:$8,500.00 F.O.B. Houston, TX

SPECIFICATIONS:

Machine Type - H-frame hydraulic powered
Capacity - 50-tons
Ram Travel - 16 inches
Pressing Ram Speed - 11 i.p.m.
Return Ram Speed  - 20 i.p.m.
Horse Power  - 2 HP
Hydraulic Pump Combination power unit
Controls On/Off switch with joystick hydraulic control
Oil Capacity - 3 U.S. gallons approx.
Weight - 1200 lbs
Overall Height - 94 inches
Base Width - 55 inches
Depth - 36 inches
Width Between Uprights - 44 inches
Width Between Table Channels - 8 1/4 inches
Maximum Ram to Table - 41 3/4 inches
Minimum Ram to Table - 0 inches
Voltage • Available 110 / 220-volt single phase
.

STANDARD EQUIPMENT:

Frame
Cylinder
Two forged steel table plates
Pressure Gauge
Lifting Chain

FEATURES:

• Made in the U.S.A.

• 110/220-volt single-phase motor makes for greater portability.

• Welded steel frame for rigidity. Fully assembled.

• Low operating pressures. Operating PSI 3537 at 50 ton.

• Double acting cylinder, utilizes the pulling force to raise and lower the table via chains, eliminating the need for hoist assemblies.

• Fast, quite, dependable, economical price, smooth operating press that is very simple to operate.

• Heavy adjustable table can be set to a comfortable work height. Massive table pins keep table securely in place during the pressing operations.

• Pressure preset and locked out at factory for maximum pressing, Safety relief valve

• The motor is a powerful 2 HP power unit for study quiet oil flow.

• 4-Way valve with joystick control operation for easy one hand machine operation.

• Rapid advance of the ram to the work piece, when contact is made the machine shifts into the pressing mode.

• Two steel table plates
45° 7.5" x 7.5"
30° 4.3" x 74.3"

Rectangle 90° H x W 9" x 18.1"
45° H x W 9" x 9"
30° H x W 9" x 4.3"

Blade: Speed 95, 150, 213, 321 fpm
Size 1" x 11.6' x .035"
(27mm x 3505mm x 0.9mm)
Guides Tungsten Carbide

MACHINE FEATURES

Machine Structure & Design:
► Oversized hydraulic cylinder plus precision ground hinge support and guide the rugged saw frame through the entire cutting cycle. Special wear resistant DU bushing is used to endure durability and long use life.
► Specially designed heavy-duty cast iron swivel center features straight and miter cuts from 90 to 30 deg (backwards) with quick setting and precise positioning. It enables smooth turning of the saw frame for each angle viable via the large easy-to-read mitering scale. Turn Table for material support swivels automatically at miter adjustment.
► Large rugged base with built-in coolant & hydraulic systems offers both sound stability & all-in-one convenience.

Blade Drive:
► A 2 hp motor, heavy-duty reducer, and variable step drive assembly with excellent mechanical design feature the essentials for production cutting.
► The 4-speed transmission is equipped with the best worm gear speed reducer. The worm shaft is hardened and ground. Together, they provide quiet, powerful, and trouble-free drive.

Blade Guidance & Lubrication System:
► Carbide blade guides with roller bearings pre-align the blade before entering carbide blade guides. This feature reduces wear on blade guides and blade, thus enhancing blade life.
► The rigid guide arms are mounted on an extra wide precision ground dovetail slide for more solid and supportive surface. This rigid design owes to use of superior cast-iron which greatly reduces vibration and achieves better cutting result.
► Two additional guides located on a central axis support the blade from the top, giving it extra penetrating force. The carbide guides are relieved to allow coolant flow to lubricate and cool the blade as well as work piece.
Integral coolant system.Blade brush to remove chips from blade gullet.

Control & Automation:
► Down feed rate & cutting pressure control. The feed rate may be adjusted by setting the dial between 0 and 10 via the hydraulic down feed valve. The vast range of adjustment allows proper setting which results in longer blade life, shorter cutting times, and better finishes.
► The control panel is clearly arranged and conveniently located on front of the machine, eliminating the need for the operator to reach over a moving blade.
► Built-in hydraulic unit includes hydraulic motor, pump, and hydraulic tank to offer the convenience
of raising the saw head automatically after cut-off. This advanced built-in design with quality components will bring you noiseless and hassle-free operation.
► A work height selector is located over the hydraulic cylinder and is used to adjust the blade to minimum clearance height over the work.

Material Clamping & Feeding:
► Cast iron vises with replaceable extension plate
Secure clamping via a dependable manual lead screw system with anti-slip hand wheel. base with built-in coolant & hydraulic systems offers both sound stability & all-in-one convenience.

We are an authorized dealer for: 

Technical Machine Sales Inc. | 521 Delia Drive |  Longview, Texas | 75601

Phone (903) 753-1955