Home
About TMSI
Contact Us

Back

ENGINE LATHES

ONE (1) NEW SHARP ENGINE LATHE, MODEL 1640 LV

SPECIFICATIONS:
" Capacity
" Swing Over Bed.................................................................................. 16"
" Swing Over Cross Slide....................................................................... 8-3/4"
" Swing Over Gap.................................................................................. 24-3/8"
" Distance Between Centers................................................................... 40"

" Headstock
" Spindle Nose Type.............................................................................. D1-8 Camlock
" Spindle Bore........................................................................................ 3- 1/16"
" Spindle Speeds.................................................................................... (12) 20-2,000 rpm
" Taper of Spindle Bore.......................................................................... MT#6
" Taper of Center.................................................................................... MT#4

" Threads and Feeds
" Longitudinal Feeds - in/rev.................................................................... (18) 0.002 - 0.032"
" Cross Feeds - in / rev {#}..................................................................... 0.0001 -0.0094" {12}
" Inch Threads (#)................................................................................... 4-56 tpi {36}
" Metric and Module Threads {#}............................................................ 0.5-7mm {17}
" D.P. Threads (36)..................................................................................4-56 mm
" Leadscrew Pitch, Diameter 4 tpi,........................................................... 1-3/8"

" Carriage
" Cross Slide Width................................................................................. 8.7"
" Compound Rest Travel......................................................................... 4.9"
" Compound Width................................................................................. 4.5"

" Bed
" Bed Length........................................................................................... 59"
" Bed Width ............................................................................................11-3/4"

" Tailstock
" Quill Travel (graduated)......................................................................... 5"
" Quill Diameter....................................................................................... 2-1/4"
" Quill Taper............................................................................................ MT#4

" General
" Spindle Motor....................................................................................... (220V /60/3) 7-1/2 hp
" Net Weight (approx.)............................................................................. 3,600 LBS

STANDARD EQUIPMENT:
" 3-Jaw Chuck 10"
" Face Plate (16")
" Steady Rest (1/2" to 6")
" Follow Rest
" Coolant System
" Full Length Splash Guard
" American Toolpost
" Halogen Worklight
" Longitudinal Carriage Stop
" Tailstock
" Tool Kit includes:
Machine Manual, Half Nut Wrench, Wrench 17m, 19m, Set of 6 Allen wrenches, Phillip Screw Driver, Flat Head Screw Driver, Oil can, Grease Gun, Rear Way Cover Bracket, Pin for Indicator, Can of Paint

INSTALLED OPTIONS:

" Newall C80 D.R.O. Factory Installed
" 4 - Jaw 12" BTC Chuck
" Roller Jaws for Steady Rest
" Jacobs Drill Chuck with Arbor (0-1/2") MT#4
" Aloris Quick Change Tool (7 pcs) Holder Set
" Live Center - MT#4

FEATURES:
" D1-8 Camlock, 3" Hole
" Direct Selection For Inch/Metric Threads
" One Piece Cast Meehanite Bed
" 7-1/2 Hp Spindle Motor
" Digital Variable Speed (DVS) on "LV" Models
" "LV" Models wired at 220v only.

Sharp 1640LV Lathe: $17,850.00
Newall C80 DRO $2,495.00
Installed Accessories (see below) $2,532.00

Total Machine Price (FOB Longview, TX) $22,877.00

ONE (1) USED AXELSON 16" x 126" ENGINE LATHE

ONE (1) USED AXELSON 16" x 126" ENGINE LATHE
ITEM NO. R-1008

SPECIFICATIONS:
Serial Number 4257
Year 1954

Remanufactured by Gates in Houston, TX 2004, SOFT WAY MACHINE

Capacity:
Swing over Bed Ways & Carriage Wings 18-1/2"
Swing over Cross Slide 11-1/2"
Distance Between Centers, Base 30"
Machine, Tailstock Flush
Permissible Tailstock Overhang 4"
Std Tool Shank Dimensions 5/8" x 1-3/8"

Dimensions:
Bed Width 16-7/8"
Height, Floor to Center Line of Spindle 41-5/16"
Carriage Ways (Center to Center) 14-3/4"

Threading and Feed Capacity:
Number of Threads 54
Range of Threads per Inch 1-1/2 to 92
Number of Feeds 54
Range of Feed per Revolution of Spindle 0.0027" to 0.1665"

Diameter of Lead Screw 1-5/16"
Lead Screw Threads per Inch (Acme) 4
Diameter of Feed Rod 7/8"
Width and Pitch of Rack 1-1/2" - 10

Motors:
Drive Motor, 220/440/3/60 10 HP
Coolant pump, 220/440/3/60 ¼ HP

Tailstock:
Length of Bearing on Ways 12-3/8"
Diameter of Tailstock Spindle 2-7/8"
Travel of Tailstock Spindle 9"
Maximum Set-Over Toward Operator 1"
Maximum Set-Over Away From Operator 1-1/4"

Headstock:
Spindle Bearings 2 Front; 2 Rear
Spindle Nose D-1 6" Camlock
Diameter of Hole Thru Spindle 1-9/16"
Spindle Speed Range, Std. (60 Cycle) 13 to 1127 rpm
Number of Spindle Speeds 24
Centers, Morse Taper No. 4

Carriage:
Length of Bearing on Ways 26-3/4"
Width of Cross Slide 8-7/8"
Travel of Cross Slide 10-5/8"
Width of Tool Slide 6-1/2"
Travel of Tool Slide 4-3/4"

Taper Attachment:
Length of Taper Turned at 1 Setting 15-1/4"
Maximum Taper per Foot 4"
Maximum Taper in Degrees (w/Center Line) 9-1/2"

Floor Space Required 10'11" x 44"
Approximate Weight 6000 Lbs.

ACCESSORIES:

Tool Post & Tool Holders

2 Steady Rest

Taper Attachment

1 Drill Chuck

4 Jaw Chuck, 15"

6 Jaw Chuck, 12"

1 Bull Center

1 Live Center

1 Boring Bar

PRICE FOB Longview, TX (AS IS WHERE IS) $13,900.00

ONE (1) USED DAEWOO 20" X 60" ENGINE LATHE
ITEM NO. R-1007

SPECIFICATIONS:
Serial Number...................................................................................................... 221009
Model ...................................................................................................................DST20
Height of Center...................................................................................................10"
Swing Over Bed................................................................................................... 20"
Swing Over Carriage........................................................................................... 13"

MAIN SPINDLE:
Type of Nose........................................................................................................ D1-8
Bore....................................................................................................................... 3"
Taper of Center.....................................................................................................MT No. 5

Spindle Speeds(12)................................................................................................Ranges 25 - 1500 rpm

CARRIAGE:
Cross Slide Travel................................................................................................ 10-1/2"
Tool Slide Travel................................................................................................... 6"

Center Distance.................................................................................................... 60 inches

FEEDS:
Changes 64............................................................................................................. 0.0008-0.0236" / rev

THREADS:
Metric..................................................................................................................... 0.5 - 7mm Pitch
Whitworth............................................................................................................... 56 - 4 T.P.I.
Module................................................................................................................... 0.25 - 3.5Md
DP.......................................................................................................................... 112 - 8DP

TAILSTOCK
Center..................................................................................................................... MT No. 5
Travel...................................................................................................................... 8"

BED:
Width...................................................................................................................... 16-1/2"
Length.....................................................................................................................90-1/2 inch

Motor:
Main Motor........................................................................................................... 220/440/3/60 AC 10 HP
Coolant pump......................................................................................................... 220/440/3/60 AC ¼ HP

Floor Space required.............................................................................................. 40 x 120inch
Approximate Weight.............................................................................................. 5550 Lbs.

ACCESSORIES:

1-10" 6 JAW SELF CENTERTING CHUCK

1-JACOBS COLLET CHUCK WITH COLLETS, 1/16" THROUGH 1 3/8"

2-STEADY RESTS, ROLLER JAWS

1 ALORIS QUICK CHANGE TOOLPOST WITH SIX (6) TOOLHOLDERS

1 TAPER ATTACHMENT

1 WORK LIGHT

PRICE FOB Longview, TX (AS IS WHERE IS) $15,335.00

ONE (1) USED DAEWOO 20" X 78"ENGINE LATHE
ITEM NO. R-1006

SPECIFICATIONS:
Serial Number...................................................................................................... 260017
Model ...................................................................................................................DST20
Height of Center...................................................................................................10"
Swing Over Bed................................................................................................... 20"
Swing Over Carriage........................................................................................... 13"

Spindle Speeds(12)................................................................................................Ranges 25 - 1500 rpm

Center Distance.................................................................................................... 78 inches

FEEDS:
Changes 64............................................................................................................. 0.0008-0.0236" / rev

Floor Space required.............................................................................................. 40 x 140inch
Approximate Weight.............................................................................................. 7050 Lbs.

ACCESSORIES:

1-12" 6 JAW SELF CENTERTING CHUCK

1-15" 4 JAW CHUCK

2-STEADY RESTS, ROLLER JAWS

1 ALORIS QUICK CHANGE TOOLPOST WITH SIX (6) TOOLHOLDERS

1 WORK LIGHT

PRICE FOB Longview, TX (AS IS WHERE IS) $17,450.00